avland.ro Web analytics

Procesor sunet Match DSP incl. EPC 5.2 - Procesoare sunet Match DSP incl. EPC 5.2
Procesor sunet Match DSP incl. EPC 5.2 - Procesoare sunet Match DSP incl. EPC 5.2 Procesor sunet Match DSP incl. EPC 5.2 - Procesoare sunet Match DSP incl. EPC 5.2 Procesor sunet Match DSP incl. EPC 5.2 - Procesoare sunet Match DSP incl. EPC 5.2 Procesor sunet Match DSP incl. EPC 5.2 - Procesoare sunet Match DSP incl. EPC 5.2

Procesor sunet Match DSP incl. EPC 5.2

Cod produs:DSP incl. EPC 5.2
Garantie:12 luni
1.399,00 Lei
*pretul contine TVA
Cant:     - SAU -   Adaugă in Wishlist Compară produs
*Pentru a confirma disponibilitatea de ridicare a unei comenzi va rugam sa ne CONTACTATI

Procesor sunet Match DSP incl. EPC 5.2

MATCH DSP with integrated Easy Plug Cable  EPC 5.2 for easy installation 

Digital 6-channel signal processor with 56 bit DSP


Easy to install, easy to adjust – the MATCH DSP is the perfect solution for smaller sound systems, which are driven by the original car radio. Its layout not only allows classical configurations (front L/R, rear L/R + subwoofer) but as well fully active front systems including subwoofer and center speaker. The versatile AUX input manages additional sources.

Nevertheless the reduction to the basics is solely limited to the number of channels – the well-known PC software and the technology inside this stunning device is as perfect as every other product from Audiotec Fischer. 56 bit signal processing, top-notch converters from Asahi Kasei and an uncompromising internal power supply care for outstanding measuring results and exceptional sound quality, both redefining the standards not only in this segment.

  • Windows interface – communication via USB 2.0
  • MicroSD slot to upload DSP settings without having to connect the DSP to a PC
  • Special audio DSP with a resolution of 56 bits – optimized for highest sound quality
  • Freely configurable inputs and outputs
  • Graphical 30-band EQ per channel with the “fine adjustment” of the individual bands in 1/24 octave steps and time correction in 7-mm steps, all established filter characteristics are available and much more
  • Inputs: 4 x highlevel, 1 x AUX stereo phone jack 3.5 mm, 1 x remote in, 1 x control input, MicroSD and USB
  • Outputs: 6 x RCA and remote output
  • Extremely compact dimensions: 44 x 185 x 100 mm

• Inputs: 4 x Highlevel speaker input; 1x Aux stereo phone jack 3,5mm; 1 x Remote In 
• Outputs: 6 x RCA/Cinch; 1 x Remote Out 
• Input Sensitivity: Highlevel 5 - 1 0 Volts; Aux 100mV 
• Output voltage: 4 Volts 
• Frequency response: 10 - 22.000 Hz 
• Signal-to-noise ratio: 105 dB 
• Distortion (THD+N):     < 0,004% 
• Crosstalk: > 90 dB 
• Power supply: 9.6 - 18 Volts (5 sec. down to 6 V olt) 
• DSP resolution: 56 Bit 
• DSP power: 172 MHz 


Power Save Mode
The Power Save Mode is incorporated in the basic setup. It allows to significantly reduce the power consumption of the amplifiers that are connected to the MATCH DSP once there’s no input signal present for more than 60 seconds. Please note that in many up-to-date cars with “CAN” or any other internal bus structures it may happen that the radio remains “invisibly” turned on for up to 45 min. even after leaving the car! Once the “Power Save Mode“ is active the remote output and therefore the connected amplifiers will be turned off. The MATCH DSP will reactivate the remote output within a second if a music signal is applied. It is possible to either modify the turn-off time of 60 sec. or completely deactivate the “Power Save Mode” via the PC-tool software. In basic configuration the „Power Save Mode“ is always activated.

Start-Stop capability
The switched power supply of the MATCH DSP assures a constant internal supply voltage even if the battery’s voltage drops to 6 Volts during engine crank.

The intelligent highlevel input
The 4-channel fully-differential highlevel input is equipped with Audiotec Fischer’s unique DEP circuit (Diagnosis Error Protection), means that OE car radios with speaker diagnosis function will not generate any undesired error logs if this DSP is connected.


4 x High level speaker Input
1 x AUX stereo phone jack 3.5 mm
1 x Remote In

Input sensitivity

Highlevel 10 Volts RMS

Lowlevel 2.5 Volts RMS (only usable with RCA/Cinch adaptor)


6 x RCA
1 x Remote out

Output voltage

4 Volts RMS

Frequency response

10 - 22.000 Hz

DSP bandwith

56 Bit

DSP processing power

172 MHz

Signal converter

A/D Asahi Kasei
D/A Asahi Kasei

Signal-to-noise ratio

105 dB (A-weighted)

Total harmonic distortion (THD+N)

< 0.004 %

IM distortion (IMD)

< 0.008 %


> 90 dB @ 1kHz

Operating Voltage

9,6 - 18 Volts, short drops down to 6 Volts acceptable

Current draw

< 500 mA

Additional features

Control Input, Micro SD, USB

(H x W x D)

Spune-ţi opinia

Notă: Codul HTML este citit ca şi text!

Rău           Bun